제품센터
PRODUCTS CENTER
Product categories
전자종이 모듈 1.54 인치 작은 크기 200x200 E Ink 패널 Arduino, Raspberry Pi, STM32 컬러 e-paper
제품 설명
DESPI-K154Z90은 1.54인치 SPI 컬러 전자 종이 디스플레이 GDEH0154Z90용으로 설계되었습니다. 굿디스플레이 1.54인치 전자종이 디스플레이의 구동 전압을 높일 수 있다. 이러한 전자 종이 모듈은 일단 업데이트되면 전원이 필요하지 않으며 실제로 완전히 연결을 끊을 수 있으며 컨텐츠는 디스플레이에 무기한 유지됩니다.
사용자가 테스트할 수 있는 6핀 터치패널과 6핀 전면등 인터페이스도 보존했다. 또한 이 모듈 보드에는 128M비트(16M바이트) 용량의 직렬 NOR 플래시 메모리인 플래시 칩 W25Q128이 포함되어 있어 사용자가 사진, 라이브러리 및 기타 관련 데이터를 쉽게 저장할 수 있습니다. 그리고 SD 카드 슬롯도 모듈에 예약되어 있어 사용자가 마이크로 SD 카드를 추가할 수 있습니다. 따라서 플래시 칩과 SD 카드 슬롯은 사용자가 더 많은 스토리지를 필요로 할 때 사용합니다.
관련 데이터시트는 데이터시트 & 파일 섹션 아래에 있습니다.
또한 기타 24핀 1.54 전자 종이 디스플레이 모듈도 있습니다. 필요하신 경우 문의해 주십시오.
특징
● SPI interface. It can be used on Raspberry Pi/Raspberry Pi Pico/ Arduino/ EPS8266/ ESP32/ STM32 Platform. We could provide the driving board, if you need, contact us please.
● It integrated Flash chip and SD card slots for expanded development
● Help users to learn how to drive the EPD with 6 PIN touch panel and 6 PIN front light
● It has 3 LED lights, each LED light can be directly controled by the expansion pins. (Please refer to the PIN description.)
![]() |
||
![]() |
PINS FOR EPD MODULE
1. Pins for EPD
1) BUSY: BUSY signal of e-paper. When the e-paper is refreshing, the BUSY pin sends out "busy" signal to MCU, the MCU can not read and write the e-paper IC; When the e-paper refresh is completed, the BUSY pin sends out "free" signal, the MCU can read and write the e-paper IC. GDEW series e-paper busy state is high level (GDEH series is low level), and free state is opposite.
2) RES: Reset signal of e-paper. Low level effective.
3) D/C: Data/ Command selection. High level for data, low level for command.
4) CS: Chip selection. Low level effective.
5) SCK: SPI serial communication clock signal line.
6) SDI: SPI serial communication data signal line.
7) GND: Negative power supply.
8) 3.3V: Positive power supply
2. Expanded Pins
1) SI: Master Output Slave Input for SPI: INT pin for TP.
2) SO: Master Input Slave Output for SPI: RST pin for TP.
3) SCK: Clock signal line for SPI: SCL pin for TP.
4) CS0: Chip selection for Flash: SDA pin for TP.
5) CS1: Chip selection for SD.
6) LED1: Control pin for LED1.
7) LED2: Control pin for LED2.
8) LED3: Control pin for LED3.
DESPI-K154-SCH
DESPI-K154Z90 CAD Drawing
GDEH0154Z90 Specification
IC Driver SSD1681
GDEH0154Z90 STM32 Sample Code
GDEH0154Z90 Arduino Sample Code
GDEH0154Z90 ESP32 Sample Code
GDEH0154Z90 Raspberry Pi Pico Sample Code
佳显电子
연락처
제품 문의 info@good-display.com
기술 지원 service@good-display.com
불만 제안 complaint@good-display.com
©2021-2024 DALIAN GOOD DISPLAY CO., LTD. All Rights Reserved. 辽ICP备08000578号-1 power by:300.cn Dalian