제품센터
PRODUCTS CENTER
Product categories
저전력 소비1.54 인치 E Ink 전자종이 200x200, Arduino, Raspberry Pi, STM32 e-paper 모듈 고 대비
제품 설명
DESPI-K154D67 1.54인치 SPI전자 신문 디스플레이 GDEH0154D67을 위해 설계되었다.그것은 좋아 디스플레이의 1.54인치 전자 신문 디스플레이의 운전 전압을 높일 수 있다.없는 힘은 –한 다음 동력 여러분 영상을 이미지를 무기한으로 보유하고 있다.일단 이러한e-paper 모듈들은 어떤 권력이 필요하지 않고 실제로 완전히 차단될 수 있어. 그리고 그 내용을 디스플레이에 영원히 있을 것이다 업데이트된다.
또한 사용자들을 테스트할 수 있는 6 핀 터치 패널과 6 핀 현관에 불을 인터페이스를 보존한다.그리고 이 모듈 보드, 사용자가 손쉽게 사진, 도서관과 다른 관련 데이터를 저장하기 플래시 칩 W25Q128 128M-bit(16M-byte)의 용량에 있는 연쇄 부정 논리합 플래시 메모리가 있습니다.그리고 SD카드 슬롯 또한 이용자들은 여분의 마이크로 SD카드 추가해 달라고 택할 수 있는 모듈에 예약되어 있다.따라서, 플래시 칩과 SD카드 슬롯 수납에 대한 사용자 필요성을 다루고 있다.
관련 datasheet은 Datasheets&파일 섹션을 받고 있다.
우리는 또한 혹시 어떤 니즈를 가지고 있습니다. 우리에게 연락하세요 다른 24 핀 2.54e-paper 디스플레이 모듈을 가지고 있다.
특징
● SPI interface. It can be used on Raspberry Pi/Raspberry Pi Pico/ Arduino/ EPS8266/ ESP32/ STM32 Platform. We could provide the driving board, if you need, contact us please.
● It integrated Flash chip and SD card slots for expanded development
● Help users to learn how to drive the EPD with 6 PIN touch panel and 6 PIN front light
● It has 3 LED lights, each LED light can be directly controled by the expansion pins. (Please refer to the PIN description.)
|
|||
|
PINS FOR EPD MODULE
1. Pins for EPD
1) BUSY: BUSY signal of e-paper. When the e-paper is refreshing, the BUSY pin sends out "busy" signal to MCU, the MCU can not read and write the e-paper IC; When the e-paper refresh is completed, the BUSY pin sends out "free" signal, the MCU can read and write the e-paper IC. GDEW series e-paper busy state is high level (GDEH series is low level), and free state is opposite.
2) RES: Reset signal of e-paper. Low level effective.
3) D/C: Data/ Command selection. High level for data, low level for command.
4) CS: Chip selection. Low level effective.
5) SCK: SPI serial communication clock signal line.
6) SDI: SPI serial communication data signal line.
7) GND: Negative power supply.
8) 3.3V: Positive power supply
2. Expanded Pins
1) SI: Master Output Slave Input for SPI: INT pin for TP.
2) SO: Master Input Slave Output for SPI: RST pin for TP.
3) SCK: Clock signal line for SPI: SCL pin for TP.
4) CS0: Chip selection for Flash: SDA pin for TP.
5) CS1: Chip selection for SD.
6) LED1: Control pin for LED1.
7) LED2: Control pin for LED2.
8) LED3: Control pin for LED3.
DESPI-K154D67 CAD Drawing
DESPI-K154-SCH
GDEH0154D67 Specification
IC Driver SSD1681
GDEH0154D67 Bitmap Conversion
GDEH0154D67 STM32 Sample Code
GDEH0154D67 Arduino Sample Code
GDEH0154D67 ESP8266 Sample Code
GDEH0154D67 ESP32 Sample Code
GDEH0154D67 Raspberry Pi Sample Code
GDEH0154D67 Raspberry Pi Pico Sample Code
佳显电子
연락처
제품 문의 info@good-display.com
기술 지원 service@good-display.com
불만 제안 complaint@good-display.com
©2021-2024 DALIAN GOOD DISPLAY CO., LTD. All Rights Reserved. 辽ICP备08000578号-1 power by:300.cn Dalian